Monitoring Network Performance with Service OAM
- 12 Articles
- Updated on Apr 14, 2026
- Published on Dec 15, 2021
Overview
This article describes how to use the Performance Assurance Agent (PAA™) for monitoring network performance.
The Performance Assurance Agent (PAA) is a hardware-assisted active-measurement function that computes Layer-2 or Layer-3 (IPv4...
- Updated on Jan 25, 2024
- Published on Dec 15, 2021
Service OAM (SOAM) is a layer-2 protocol used for Connectivity Fault Management (CFM) and Performance Monitoring (PM) in a Carrier Ethernet Network (CEN) and encompasses the fault management and performance management capabilities of the Skylight pe...
- Updated on Jan 25, 2024
- Published on Dec 15, 2021
Link Trace Messages (LTM) are multicast frames transmitted by a MEP to track the path (hopby- hop) to a destination MEP. Each receiving MEP sends a trace route reply directly to the originating MEP, and regenerates the trace route message. LTM are d...
- Updated on Jan 25, 2024
- Published on Dec 15, 2021
Loopback messages are unicast frames transmitted by a MEP. Sending a high volume of loopback messages can test the bandwidth, reliability or jitter of a service. A MEP can send a loopback to any MEP or MIP in the service. Loopback messages are discu...
- Updated on Apr 15, 2022
- Published on Dec 15, 2021
DMM measurements (delay and delay variation) work as follows.
A DMM frame is sent from the originating unit to the remote unit. When the DMM frame is received by the remote unit, it sends a DMR to the originating unit. The reception of the DMM fra...
- Updated on Mar 30, 2022
- Published on Dec 15, 2021
To set up packet loss instances
Access the page SOAM ▶CFM ▶Packet Loss ▶Configuration .
A listing of all existing packet loss instances is displayed.
Click Add to create a packet loss instance or click the packet loss instance inde...
- Updated on Jan 25, 2024
- Published on Dec 15, 2021
Synthetic loss measurement is used to measure the frame loss ratios (near-end and far-end) between two MEPs. Measurements and calculations are performed at one end only. You have to set up the SLM instance on the unit that you want to perform and di...
- Updated on Jan 25, 2024
- Published on Dec 15, 2021
Use this page to view a summary of all CFM interfaces or manage the details related to a selected interface.
To view CFM interface information
Access the page SOAM ▶CFM ▶Interface .
The CFM Interfaces page opens. All available CFM inte...
- Updated on Apr 15, 2022
- Published on Dec 15, 2021
The VSP function is used to reflect VSP (vendor-specific) frames to the sender.
Note: This function is to be used only with VSP when connecting to Layer-2 VSP actuator devices.
To set up the VSP function
Access the page SOAM ▶C...
- Updated on Jan 25, 2024
- Published on Dec 15, 2021
The MIP Half-Function (MHF) default parameters control the MHF creation for VIDs that are not attached to a Maintenance Association within a VLAN component. For each component port, a VID is attached to a Maintenance Association at a specific MD lev...
- Updated on Jan 25, 2024
- Published on Dec 15, 2021
This article describes the Service Availability (SA) function and how to set it up in your Metro Ethernet Network. The SA function is used to determine the number of unavailable seconds and other counters for a specific service. You can use the SA f...
- Updated on Sep 11, 2024
- Published on Dec 15, 2021
Two-Way Active Measurement Protocol (TWAMP) is a protocol used to measure round-trip IP performance between any two TWAMP-enabled units deployed in a network. With TWAMP, you can reliably perform in band, round-trip performance measurements and iden...