--- title: "Starting the Management Web Interface" slug: "starting-the-management-web-interface-7" tags: ["interface ", "SSL", "certificate", "management", "assurance sensor 24.07", "Assurance Sensor GT", "Assurance Sensor LT-S", "Assurance Sensor GT-S", "Assurance Sensor LX-S", "Assurance Sensors", "25.07"] updated: 2026-07-28T15:16:19Z published: 2026-07-28T15:16:19Z canonical: "docs.crossworkassurance.cisco.com/starting-the-management-web-interface-7" --- > ## Documentation Index > Fetch the complete documentation index at: https://docs.crossworkassurance.cisco.com/llms.txt > Use this file to discover all available pages before exploring further. # Start the Management Web Interface ## Physical Connection to the Unit The first time you connect to the unit before logging in, you must connect the LAN port on the management station to the management port on the front of the unit. This allows you to log in and configure the unit for the first time. For example, you can set the unit's time and date and create other logical interfaces so you can connect through a LAN or WAN. The default management port is the Management port. ### Log In After you establish a physical connection to the equipment, you can log in. There are various ways to log in depending on how the unit has been configured. Typically, connect to the unit for the first time using the Management port. Then configure another interface, e.g. Network, for in-band management through the network. **First-Time Login** 1. The unit is pre-configured with a default static IP of 192.168.1.254/24, therefore, you must assign your workstation or terminal with a static IP address belonging to the same subnet as the unit. For example 192.168.1.2. 2. Start your Web browser and enter the following in the address bar: **https://192.168.1.254.** The login page for the unit opens. **Note:** This is the factory default IP address of the unit. 3. Log in with the default credentials: You are redirected to the password change page. - Username: admin - Password: admin 4. Change the default password. See [Change the Default Password](/v1/docs/starting-the-management-web-interface-lx-lt-gt#change-the-default-password)for more information. 5. If you are using static IP addresses, modify the unit's IP address to be unique, thereby avoiding duplicate IP addresses with other factory default units. As an alternative, you can configure the unit to use DHCP. For more information on modifying IP addresses, using DHCP, and other options for logical interfaces, refer to "Configuring Logical Interfaces". ### Change the Default Password After you log in with the default credentials, you are redirected to the password change page: ![image.png](https://cdn.document360.io/01d1de5e-a375-4fbc-aa82-666ac04c2113/Images/Documentation/image-AE5F3BBO.png?sv=2026-02-06&spr=https&st=2026-11-16T06%3A06%3A19Z&se=2026-11-16T07%3A06%3A19Z&sr=b&sp=r&sig=%2FaM7ZZIwGVDwoZI24q5EMNs0wAq5omTIE4GS%2F2mPUB0%3D) **Note:** This page will not allow access to any other part of the Web UI until the password has been changed. **Caution:** When logging in initially via the CLI, you are prompted to change the default password while the unit is in the factory-default state. Only the following commands are available until you complete the password change: `edit password` ,`exit`, `board show info`, `logout`, `firmware version`, `session show status`, and `configuration changes`. Using other commands returns an error. You can use the `clear password` option to change the password. 1. Enter a new password between one and 128 characters (all characters are accepted). For specific details, see also, [Password Considerations](/v1/docs/starting-the-management-web-interface-lx-lt-gt#password-considerations) below. 2. Confirm a new password. Your password has now been successfully changed. ![image.png](https://cdn.document360.io/01d1de5e-a375-4fbc-aa82-666ac04c2113/Images/Documentation/image-O7GBLIV8.png?sv=2026-02-06&spr=https&st=2026-11-16T06%3A06%3A19Z&se=2026-11-16T07%3A06%3A19Z&sr=b&sp=r&sig=vrsNGRZCBHcYLEJfrcqywYteHn1vw3kU78TYbuEWnIs%3D) #### Example Error Messages **Mismatch Error** If the new password and the confirmation do not match or do not meet the complexity requirements, the user will receive the following error message: ![image.png](https://cdn.document360.io/01d1de5e-a375-4fbc-aa82-666ac04c2113/Images/Documentation/image-M9YK16DZ.png?sv=2026-02-06&spr=https&st=2026-11-16T06%3A06%3A19Z&se=2026-11-16T07%3A06%3A19Z&sr=b&sp=r&sig=JEkh9c5jTkNk40Fv%2FusmBVj74zomkdNzvhy7fLG7GVg%3D) **Password Reuse Error** The password cannot be identical to the default password **admin** nor can you select a password you have already used. ![image.png](https://cdn.document360.io/01d1de5e-a375-4fbc-aa82-666ac04c2113/Images/Documentation/image-YOW56RXR.png?sv=2026-02-06&spr=https&st=2026-11-16T06%3A06%3A19Z&se=2026-11-16T07%3A06%3A19Z&sr=b&sp=r&sig=e%2FDrBsbclGG31q9%2F64YEKQ%2B7rSSJHn5zh0CS7jQTs%2Bo%3D) **Concurrent Password Change Error** If there are multiple sessions attempting the first login password change and one of them is successful, the system prevents the other sessions from continuing with the password change process. In this case you are redirected to the login page with the following error message: ![image.png](https://cdn.document360.io/01d1de5e-a375-4fbc-aa82-666ac04c2113/Images/Documentation/image-LY8DQTAQ.png?sv=2026-02-06&spr=https&st=2026-11-16T06%3A06%3A19Z&se=2026-11-16T07%3A06%3A19Z&sr=b&sp=r&sig=JD3t4%2BkGPvy3WmHMYCgveNLMiTGag0z6mnEKi5miUnM%3D) After you successfully update the password, you are redirected to the default Management Web Interface home page. **IMPORTANT:** If you try to access any other URL without finishing the initial password change, the system will refuse the request and redirect you to the password change screen. ### Log In to the Web Interface **First-Time Login (If Another Logical Interface Is Configured)** 1. Ensure your management station has a route to the equipment. 2. Launch your Web browser and enter the equipment address in the address bar, e.g. **https://192.168.1.25** (or **host_name.domain_name** if you are using a DNS). 3. The login page opens. Log in using the admin username and account password. ### Password Considerations The Management Web Interface supports a variety of authentication methods, as well as the order in which these methods are applied. You can indicate your preferred authentication order in the **System ▶Session ▶Configuration** page. The maximum permitted password length varies, depending on the authentication method you specify: - **Local Authentication:** 48 characters - **RADIUS Authentication:** 48 characters - **TACACS+ Authentication:** 64 characters If you choose to include a fallback method in your authentication order, you must ensure that the user password you choose is valid for all authentication methods that you want to use. For example, if you want to use TACACS+ authentication when logging in—with local authentication as the fallback method—your TACACS+ password cannot exceed 31 characters. Any passwords that are longer than 31 characters will be truncated and unusable by the local authentication system, even if they are supported by the TACACS+ server. **Note:** If you plan on using a remote server for authentication, you should confirm that the remote system is functional before removing the local authentication. If you remove local authentication and the remote system is not working, you will lose access to the unit. To ensure that authentication is working on the remote server, log in then out from the unit, then access the **System ▶Agent ▶Syslog** page. You should see a syslog message indicating a successful login attempt. ### Character Limitations in URLs and User Input Fields The Management Web Interface restricts the following special characters in URLs and user input fields: - The following special characters are not allowed in any user input fields: "&","<", ">", "\n", "\r", "\t ", "'' and " " ". - The following special characters are not allowed in the URL input: "<", ">", "\n", "\r" and "\t". ### Home Page Overview The home page provides general information about the unit. To view the home page, access the page Home. For information on specific parameters displayed on the home page, refer to the following table. **Home Page Parameters (Home)** | Parameter | Description | | --- | --- | | MAC Base Address | The base MAC address of the unit. For a line card with multiple ports, the base address is the address of the first port, and the address is subsequently incremented for the second port, etc. | | Unit Identifier | The host name that identifies the unit on the network. Access the page **System ▶Configuration ▶DNS** to change the host name. | | Firmware Version | The version number of the firmware running on the unit. Access the page **System ▶Maintenance ▶Firmware** to upgrade the firmware. | | Serial Number | The serial number assigned to the unit. | | **Board Info** | | | System Uptime | The period of time that has elapsed since the unit was last restarted, whether it was following a firmware upgrade, a manual reboot or a power cycle. | | System Started | The time when the unit was last powered on as reported by the system clock. Access the page **System ▶Configuration ▶Time** to set the system clock. ***Note:** This value is reset when a power cycle is performed on the unit.* | ### Modify the Host Name The default host name (or unit identifier) is the serial number assigned to the unit; it is displayed in the banner at the top of the screen after logging in. You can change the host name to a name more meaningful to your organization or use other DHCP host name options. The **Host Name** identifies the unit on the network and can be used when you log in to the unit, as shown in the figure in the section "About the Management Web Interface". **Note:** The host name is also displayed in the CLI prompt and is added to system log entries to help you identify the unit more clearly. **To Modify the Host Name** 1. Access the page **System ▶Configuration ▶DNS**. 2. Enter the new unit identifier in the Host Name field. 3. Click **Apply** to save your changes. For information on specific parameters, refer to the following table. **DNS Parameters (System ▶Configuration ▶DNS)** | Parameter | Description | | --- | --- | | Use DHCP Results | Enables the use of DNS settings obtained via DHCP. You can then select the interface to use for obtaining DHCP information using the **From Interface** control. | | Use DHCP6 Results | Enables use of DNS settings obtained via DHCPv6. You can then select the interface to use for obtaining DHCPv6 information using **From Interface (DHCP6)**. | | Host Name | The name that identifies the unit on the network. A maximum of 64 alphanumeric characters is supported. This parameter is only valid when DHCP host name is set to Current Hostname. ***Note:** See caution below* | | DHCP Host Name | The source of the DHCP host name Possible values are: - **Current Hostname**: The host name is the string entered in the **Host Name** field. - **Serial Number (DHCP option 12)**: The host name is the serial number of the unit. - **Custom Hostname (DHCP option 12)**: The host name is the text string you enter in the field to the right of the DHCP **Host Name**. | | Field to the right of DHCP host name | This field is only used when the DHCP host name is set to **Custom Hostname**. | | DHCP Client ID | This value corresponds to DHCP option 61. It allows you to enter a text string for use as the unit's unique identifier when communicating with the DHCP host. When the text box is empty, the MAC address is used as the unit's client ID. | | From Interface | The interface used for obtaining DHCP information. ***Note:** This field is only available when the **Use DHCP Results** option is enabled.* | | From Interface (DHCP6) | The interface used for obtaining DHCP information. ***Note:** This field is only available when the **Use DHCP6 Results** option is enabled.* | | DNS Server 1 | The address of DNS server 1 is available only when Use **DHCP Results** is **not** selected. | | DNS Server 2 | The address of DNS server 2 is available only when **Use DHCP Results** is **not** selected. | | Domain | The local domain name associated with the DNS is available only when **Use DHCP Results** is **not** selected. | **Caution:** Special characters are supported in the hostname, however these special characters, ~`!@#$%^*()_+-=[]{}|;:,./? , should be used with caution because they can create some interoperability issues. These include, the inability to create a job configuration if the hostname contains the character "" \ "" or modify the hostname of any device if it includes "" \ "". Users cannot add special characters in the hostname as a reflector for session management automatically by default name; nor can they create objects and virtualize the performance monitoring data on Cisco Crosswork Assurance if the hostname contains the special characters. Lastly, users cannot create circuits and virtualize performance monitoring data for device hostname containing "" \ "" on the legacy SLA portal. **© 2026 Cisco and/or its affiliates. All rights reserved.** For more information about trademarks, please visit: [Cisco trademarks](https://www.cisco.com/c/en/us/about/legal/trademarks.html)[](https://www.cisco.com/c/en/us/about/legal/trademarks.html) For more information about legal terms, please visit: [Cisco legal terms](https://www.cisco.com/c/en/us/about/legal/terms-conditions.html)